you are here » home » Products » Expansion Modules  
Expansion Modules    
E-opto16 Expansion Module
Expandable Intelligent Monitoring Solution for your Enterprise Resources

The E-opto16 is an expandable module that has (16) dry contact inputs and is connected to any of the (4) RJ-45 expansion ports located on the front panel of the securityProbe 5E base units using standard CAT5 LAN cable.

A very wide variety of equipment that generates an output signal or voltage can be connected to each of the 16 dry contacts inputs located on the back of the E-opto16 expansion module, or E-module.

The (16) dry contact input LED status is displayed on the front panel of the E-module.

The E-opto16 E-module can be daisy chained together using the units input, or E-in and output, E-out ports located on the front panel of the E-module. These also are standard RJ-45 ports and use standard CAT cable.

These E-modules can be extended from the securityProbe 5E's base unit, or from each other up to 300 meters, or roughly 1000 feet.

Note:
The 300 meter maximum run length is not the total run length of all of the E-modules combined. This is each E-modules maximum run length from either the base unit, or from each other.

There is not any limit to how many E-modules can be connected to a single securityProbe 5E base units. This solely depends on how many sensors are connected, as up to 600 sensors can be connected to a single securityProbe 5E.

A typical application for the E-opto16 would be to connect the outputs of an alarm panel to each of the 16 dry contact inputs allowing the securityProbe 5E's full featured built in notification system to be integrated into these alarm panels, or other systems that output a voltage.
 
  Features:
  Rack Mountable 19” 1U
    Creates Dry Contact Expandability On The securityProbe 5E
    Daisy Chainable
    Standard RJ-45 Input and Output Ports For Daisy Chaining Multiple Modules
    Extendable Using Standard CAT5 LAN Cable
    16 Dry Contact Input Status LED’s
    16, 2 Wire Dry Contact Ports Configured As Opto-Isolated
 
  Specifications:
Dimension
    Size : 8.5” x 5.43” x 1.80 “
  Weight : 2.4 pounds
  Power Requirements:
    Voltage 7.0 - 9 V / >= 3 Amp
  Power Consumption:
    Typical 6.150 Watt, 0.82A
  Inputs:
    16, 2 wire dry contact inputs configured as opto-isolated
  2 wire dry contact inputs support up to 50 Volts DC and 80mA of current
  1 RJ-45 expansion module input (E-in)
  Network Interface:
    Standard 10/100 Base-T Ethernet RJ-45 port
  Status Indication:
    LED indication for Power
  LED for Network Connectivity
  LED’s for dry contact status
  Operating Environment:
    Temperature : Min. -35° C - Max. +55° C
  Humidity : Min. 20% - Max. 80%(Non-Condensing)
  Output:
    1 RJ-45 expansion module output (E-out)
  Components:
    Manufactured using highly integrated, low power surface mount technology
     to ensure long term reliability.
  MTBF:
    400,000 Hours
  Expandability/E-modules:
    Daisy chain mulitiple E-modules including E-sensor8 and E-opto16
     combined
  Uses standard RJ-45 connecttions and CAT5 LAN cable
  Data transfer rate: 115.2 KBPS
  Maximum extension cable run length: 300 meters (1000 feet)
  1 RJ-45 expansion module input (E-in)
  1 RJ-45 expansion module output (E-out)
   
  E-opto16
  E-sensor8